NAME
systemd.path - Path unit configurationSYNOPSIS
path.pathDESCRIPTION
A unit configuration file whose name ends in ".path" encodes information about a path monitored by systemd, for path-based activation. This man page lists the configuration options specific to this unit type. See systemd.unit(5) for the common options of all unit configuration files. The common configuration items are configured in the generic [Unit] and [Install] sections. The path specific configuration options are configured in the [Path] section. For each path file, a matching unit file must exist, describing the unit to activate when the path changes. By default, a service by the same name as the path (except for the suffix) is activated. Example: a path file foo.path activates a matching service foo.service. The unit to activate may be controlled by Unit= (see below). Internally, path units use the inotify(7) API to monitor file systems. Due to that, it suffers by the same limitations as inotify, and for example cannot be used to monitor files or directories changed by other machines on remote NFS file systems. When a service unit triggered by a path unit terminates (regardless whether it exited successfully or failed), monitored paths are checked immediately again, and the service accordingly restarted instantly. As protection against busy looping in this trigger/start cycle, a start rate limit is enforced on the service unit, see StartLimitIntervalSec= and StartLimitBurst= in systemd.unit(5). Unlike other service failures, the error condition that the start rate limit is hit is propagated from the service unit to the path unit and causes the path unit to fail as well, thus ending the loop.AUTOMATIC DEPENDENCIES
Implicit Dependencies
The following dependencies are implicitly added:•If a path unit is beneath another
mount unit in the file system hierarchy, both a requirement and an ordering
dependency between both units are created automatically.
•An implicit Before= dependency
is added between a path unit and the unit it is supposed to activate.
Default Dependencies
The following dependencies are added unless DefaultDependencies=no is set:•Path units will automatically have
dependencies of type Before= on paths.target, dependencies of type
After= and Requires= on sysinit.target, and have dependencies of
type Conflicts= and Before= on shutdown.target. These ensure
that path units are terminated cleanly prior to system shutdown. Only path
units involved with early boot or late system shutdown should disable
DefaultDependencies= option.
OPTIONS
Path unit files may include [Unit] and [Install] sections, which are described in systemd.unit(5). Path unit files must include a [Path] section, which carries information about the path or paths it monitors. The options specific to the [Path] section of path units are the following: PathExists=, PathExistsGlob=, PathChanged=, PathModified=, DirectoryNotEmpty=Defines paths to monitor for certain changes:
PathExists= may be used to watch the mere existence of a file or
directory. If the file specified exists, the configured unit is activated.
PathExistsGlob= works similarly, but checks for the existence of at
least one file matching the globbing pattern specified. PathChanged=
may be used to watch a file or directory and activate the configured unit
whenever it changes. It is not activated on every write to the watched file
but it is activated if the file which was open for writing gets closed.
PathModified= is similar, but additionally it is activated also on
simple writes to the watched file. DirectoryNotEmpty= may be used to
watch a directory and activate the configured unit whenever it contains at
least one file.
The arguments of these directives must be absolute file system paths.
Multiple directives may be combined, of the same and of different types, to
watch multiple paths. If the empty string is assigned to any of these options,
the list of paths to watch is reset, and any prior assignments of these
options will not have any effect.
If a path already exists (in case of PathExists= and
PathExistsGlob=) or a directory already is not empty (in case of
DirectoryNotEmpty=) at the time the path unit is activated, then the
configured unit is immediately activated as well. Something similar does not
apply to PathChanged= and PathModified=.
If the path itself or any of the containing directories are not accessible,
systemd will watch for permission changes and notice that conditions
are satisfied when permissions allow that.
Unit=
The unit to activate when any of the
configured paths changes. The argument is a unit name, whose suffix is not
".path". If not specified, this value defaults to a service that has
the same name as the path unit, except for the suffix. (See above.) It is
recommended that the unit name that is activated and the unit name of the path
unit are named identical, except for the suffix.
MakeDirectory=
Takes a boolean argument. If true, the
directories to watch are created before watching. This option is ignored for
PathExists= settings. Defaults to false.
DirectoryMode=
If MakeDirectory= is enabled, use the
mode specified here to create the directories in question. Takes an access
mode in octal notation. Defaults to 0755.
TriggerLimitIntervalSec=, TriggerLimitBurst=
Configures a limit on how often this path unit
may be activated within a specific time interval. The
TriggerLimitIntervalSec= may be used to configure the length of the
time interval in the usual time units "us", "ms",
"s", "min", "h", ... and defaults to 2s. See
systemd.time(7) for details on the various time units understood. The
TriggerLimitBurst= setting takes a positive integer value and specifies
the number of permitted activations per time interval, and defaults to 200.
Set either to 0 to disable any form of trigger rate limiting. If the limit is
hit, the unit is placed into a failure mode, and will not watch the paths
anymore until restarted. Note that this limit is enforced before the service
activation is enqueued.
Check systemd.unit(5), systemd.exec(5), and systemd.kill(5)
for more settings.
SEE ALSO
Environment variables with details on the trigger will be set for triggered units. See the "Environment Variables Set on Triggered Units" section in systemd.exec(1) for more details. systemd(1), systemctl(1), systemd.unit(5), systemd.service(5), inotify(7), systemd.directives(7)systemd 252 |