NAME
epmd - Erlang Port Mapper DaemonDESCRIPTION
- epmd [-d|-debug] [DbgExtra...] [-address Addresses] [-port No] [-daemon] [-relaxed_command_check]:
- Starts the port mapper daemon.
- epmd [-d|-debug] [-port No] [-names|-kill|-stop Name]:
- Communicates with a running port mapper daemon.
Note:
On Windows the maximum number of nodes allowed in one epmd instance is 60. This
is because of limitations in the current implementation. If you need more
nodes, you should look into using and erlang based epmd implementation such as
Erlang EPMD.
- Starting the port mapper daemon:
- The daemon is started automatically by command erl(1) if the node is to be distributed and no running instance is present. If automatically launched environment variables must be used to change the behavior of the daemon; see section Environment Variables.
If argument -daemon is not specified, epmd runs as a normal
program with the controlling terminal of the shell in which it is started.
Normally, it is to be run as a daemon.
Regular startup options are described in section Regular Options.
The DbgExtra options are described in section DbgExtra Options.
- Communicating with a running port mapper daemon:
- Communicating with the running epmd daemon by the epmd program is done primarily for debugging purposes.
The different queries are described in section Interactive options.
REGULAR OPTIONS
These options are available when starting the name server. The name server is normally started automatically by command erl(1) (if not already available), but it can also be started at system startup.- -address List:
- Lets this instance of epmd listen only on the comma-separated list of IP addresses and on the loopback address (which is implicitly added to the list if it has not been specified). This can also be set using environment variable ERL_EPMD_ADDRESS; see section Environment Variables.
- -port No:
- Lets this instance of epmd listen to another TCP port than default 4369. This can also be set using environment variable ERL_EPMD_PORT; see section Environment Variables.
- -d | -debug:
- Enables debug output. The more -d flags specified, the more debug output you will get (to a certain limit). This option is most useful when the epmd daemon is not started as a daemon.
- -daemon:
- Starts epmd detached from the controlling terminal. Logging ends up in syslog when available and correctly configured. If the epmd daemon is started at boot, this option is definitely to be used. It is also used when command erl automatically starts epmd.
- -relaxed_command_check:
- Starts the epmd program with relaxed command checking (mostly for backward compatibility). This affects the following:
- *
- With relaxed command checking, the epmd daemon can be killed from the local host with, for example, command epmd -kill even if active nodes are registered. Normally only daemons with an empty node database can be killed with epmd -kill.
- *
- Command epmd -stop (and the corresponding messages to epmd, as can be specified using erl_interface:ei(3erl)) is normally always ignored. This because it can cause a strange situation where two nodes of the same name can be alive at the same time. A node unregisters itself by only closing the connection to epmd, which is why command stop was only intended for use in debugging situations.
With relaxed command checking enabled, you can forcibly unregister live
nodes.
Relaxed command checking can also be enabled by setting environment variable
ERL_EPMD_RELAXED_COMMAND_CHECK before starting epmd.
Use relaxed command checking only on systems with very limited interactive
usage.
DBGEXTRA OPTIONS
Note:
These options are only for debugging and testing epmd clients. They are
not to be used in normal operation.
- -packet_timeout Seconds:
- Sets the number of seconds a connection can be inactive before epmd times out and closes the connection. Defaults to 60.
- -delay_accept Seconds:
- To simulate a busy server, you can insert a delay between when epmd gets notified that a new connection is requested and when the connection gets accepted.
- -delay_write Seconds:
- Also a simulation of a busy server. Inserts a delay before a reply is sent.
INTERACTIVE OPTIONS
These options make epmd run as an interactive command, displaying the results of sending queries to an already running instance of epmd. The epmd contacted is always on the local node, but option -port can be used to select between instances if several are running using different ports on the host.- -port No:
- Contacts the epmd listening on the specified TCP port number (default 4369). This can also be set using environment variable ERL_EPMD_PORT; see section Environment Variables.
- -names:
- Lists names registered with the currently running epmd.
- -kill:
- Kills the currently running epmd.
Killing the running epmd is only allowed if epmd -names shows an
empty database or if -relaxed_command_check was specified when the
running instance of epmd was started.
Notice that -relaxed_command_check is specified when starting the daemon
that is to accept killing when it has live nodes registered. When running
epmd interactively, -relaxed_command_check has no effect. A
daemon that is started without relaxed command checking must be killed using,
for example, signals or some other OS-specific method if it has active clients
registered.
- -stop Name:
- Forcibly unregisters a live node from the epmd database.
This command can only be used when contacting epmd instances started with
flag -relaxed_command_check.
Notice that relaxed command checking must enabled for the epmd daemon
contacted. When running epmd interactively,
-relaxed_command_check has no effect.
ENVIRONMENT VARIABLES
- ERL_EPMD_ADDRESS:
- Can be set to a comma-separated list of IP addresses, in which case the epmd daemon will listen only on the specified address(es) and on the loopback address (which is implicitly added to the list if it has not been specified). The default behavior is to listen on all available IP addresses.
- ERL_EPMD_PORT:
- Can contain the port number epmd will use. The default port will work fine in most cases. A different port can be specified to allow several instances of epmd, representing independent clusters of nodes, to co-exist on the same host. All nodes in a cluster must use the same epmd port number.
- ERL_EPMD_RELAXED_COMMAND_CHECK:
- If set before start, the epmd daemon behaves as if option -relaxed_command_check was specified at startup. Consequently, if this option is set before starting the Erlang virtual machine, the automatically started epmd accepts the -kill and -stop commands without restrictions.
LOGGING
On some operating systems syslog will be used for error reporting when epmd runs as a daemon. To enable the error logging, you must edit the /etc/syslog.conf file and add an entry:!epmd *.*<TABs>/var/log/epmd.logwhere <TABs> are at least one real tab character. Spaces are silently ignored.
ACCESS RESTRICTIONS
The epmd daemon accepts messages from both the local host and remote hosts. However, only the query commands are answered (and acted upon) if the query comes from a remote host. It is always an error to try to register a node name if the client is not a process on the same host as the epmd instance is running on. Such requests are considered hostile and the connection is closed immediately. The following queries are accepted from remote nodes:- *
- Port queries, that is, on which port the node with a specified name listens
- *
- Name listing, that is, gives a list of all names registered on the host
| erts 13.1.5 | Ericsson AB |