ng_patch

NAME

ng_patch — trivial mbuf data modifying netgraph node type

The patch node performs data modification of packets passing through it. Modifications are restricted to a subset of C language operations on unsigned integers of 8, 16, 32 or 64 bit size. These are: set to new value (=), addition (+=), subtraction (-=), multiplication (*=), division (/=), negation (= -), bitwise AND (&=), bitwise OR (|=), bitwise eXclusive OR (^=), shift left (<<=), shift right (>>=). A negation operation is the one exception: integer is treated as signed and second operand (the value) is not used. If there is more than one modification operation, they are applied to packets sequentially in the order they were specified by the user. The data payload of a packet is viewed as an array of bytes, with a zero offset corresponding to the very first byte of packet headers, and the length bytes beginning from offset as a single integer in network byte order. An additional offset can be optionally requested at configuration time to account for packet type.

HOOKS

This node type has two hooks:

in: Packets received on this hook are modified according to rules specified in the configuration and then forwarded to the out hook, if it exists. Otherwise they are reflected back to the in hook.
out: Packets received on this hook are forwarded to the in hook without any changes.

CONTROL MESSAGES

This node type supports the generic control messages, plus the following:

NGM_PATCH_SETDLT (setdlt): Sets the data link type on the in hook (to help calculate relative offset). Currently, supported types are DLT_RAW (raw IP datagrams , no offset applied, the default) and DLT_EN10MB (Ethernet). DLT_ definitions can be found in <net/bpf.h>. If you want to work on the link layer header you must use no additional offset by specifying DLT_RAW. If EN10MB is specified, then the optional additional offset will take into account the Ethernet header and a QinQ header if present.
NGM_PATCH_GETDLT (getdlt): This control message returns the data link type of the in hook.
NGM_PATCH_SETCONFIG (setconfig): This command sets the sequence of modify operations that will be applied to incoming data on a hook. The following struct ng_patch_config must be supplied as an argument:

The csum_flags can be set to any combination of CSUM_IP, CSUM_TCP, CSUM_SCTP and CSUM_UDP (other values are ignored) for instructing the IP stack to recalculate the corresponding checksum before transmitting packet on output interface. The ng_patch node does not do any checksum correction by itself.
NGM_PATCH_GETCONFIG (getconfig): This control message returns the current set of modify operations, in the form of a struct ng_patch_config.
NGM_PATCH_GET_STATS (getstats): Returns the node's statistics as a struct ng_patch_stats.
NGM_PATCH_CLR_STATS (clrstats): Clears the node's statistics.
NGM_PATCH_GETCLR_STATS (getclrstats): This command is identical to NGM_PATCH_GET_STATS, except that the statistics are also atomically cleared.

SHUTDOWN

This node shuts down upon receipt of a NGM_SHUTDOWN control message, or when all hooks have been disconnected.

EXAMPLES

This ng_patch node was designed to modify TTL and TOS/DSCP fields in IP packets. As an example, suppose you have two adjacent simplex links to a remote network (e.g. satellite), so that the packets expiring in between will generate unwanted ICMP-replies which have to go forth, not back. Thus you need to raise TTL of every packet entering link by 2 to ensure the TTL will not reach zero there. To achieve this you can set an ipfw(8) rule to use the netgraph action to inject packets which are going to the simplex link into the patch node, by using the following ngctl(8) script:

/usr/sbin/ngctl -f- <<-SEQ 
	mkpeer ipfw: patch 200 in 
	name ipfw:200 ttl_add 
	msg ttl_add: setconfig { count=1 csum_flags=1 ops=[	\ 
		{ mode=2 value=3 length=1 offset=8 } ] } 
SEQ 
/sbin/ipfw add 150 netgraph 200 ip from any to simplex.remote.net

Here the “ttl_add” node of type ng_patch is configured to add (mode NG_PATCH_MODE_ADD) a value of 3 to a one-byte TTL field, which is 9th byte of IP packet header.

Another example would be two consecutive modifications of packet TOS field: say, you need to clear the IPTOS_THROUGHPUT bit and set the IPTOS_MINCOST bit. So you do:

/usr/sbin/ngctl -f- <<-SEQ 
	mkpeer ipfw: patch 300 in 
	name ipfw:300 tos_chg 
	msg tos_chg: setconfig { count=2 csum_flags=1 ops=[	\ 
		{ mode=7 value=0xf7 length=1 offset=1 }		\ 
		{ mode=8 value=0x02 length=1 offset=1 } ] } 
SEQ 
/sbin/ipfw add 160 netgraph 300 ip from any to any not dst-port 80

This first does NG_PATCH_MODE_AND clearing the fourth bit and then NG_PATCH_MODE_OR setting the third bit.

In both examples the csum_flags field indicates that IP checksum (but not TCP or UDP checksum) should be recalculated before transmit.

Note: one should ensure that packets are returned to ipfw after processing inside netgraph(4), by setting appropriate sysctl(8) variable:

sysctl net.inet.ip.fw.one_pass=0

HISTORY

The ng_patch node type was implemented in FreeBSD 8.1.

AUTHORS

Maxim Ignatenko ⟨[email protected]⟩.

Relative offset code by
DMitry Vagin

This manual page was written by
Vadim Goncharov ⟨[email protected]⟩.

BUGS

The node blindly tries to apply every patching operation to each packet (except those which offset if greater than length of the packet), so be sure that you supply only the right packets to it (e.g. changing bytes in the ARP packets meant to be in IP header could corrupt them and make your machine unreachable from the network).

!!! WARNING !!!

The output path of the IP stack assumes correct fields and lengths in the packets - changing them by to incorrect values can cause unpredictable results including kernel panics.

November 17, 2015

Debian

ng_patch

NAME

SYNOPSIS

DESCRIPTION